# Ethernet Settings

**Step 1: Change Adapter Settings**

*

1. **Open Network Connections**
   * Press **Win + R**, type `ncpa.cpl`, and click **OK**.
2. ![](https://sickk-services.gitbook.io/~gitbook/image?url=https%3A%2F%2Fcontent.gitbook.com%2Fcontent%2FGDLtbyiPkgQOjMQ1BLO0%2Fblobs%2F5nnuvD6By323fz6oMTDl%2Fimage.png\&width=768\&dpr=4\&quality=100\&sign=5091706c\&sv=2)
3. **Modify Ethernet Properties**

   * Right-click your Ethernet connection and select **Properties**.

   ![](https://sickk-services.gitbook.io/~gitbook/image?url=https%3A%2F%2Fcontent.gitbook.com%2Fcontent%2FGDLtbyiPkgQOjMQ1BLO0%2Fblobs%2F0SDATIkJAQytou9UYNjO%2Fimage.png\&width=768\&dpr=4\&quality=100\&sign=37802b60\&sv=2)YOU ONLY NEED THESE 2 TICKED THEN HIT OK

   **Ensure the Correct Options Are Selected**

   * In the **Ethernet Properties**, make sure only the two required options are selected.
   * Once confirmed, click **Configure** to access the advanced settings.

   ![](https://sickk-services.gitbook.io/~gitbook/image?url=https%3A%2F%2Fcontent.gitbook.com%2Fcontent%2FGDLtbyiPkgQOjMQ1BLO0%2Fblobs%2F8jF5ZuLFp47PyocRVHgr%2Fimage.png\&width=768\&dpr=4\&quality=100\&sign=aa37f9b0\&sv=2)

   * Apply the following changes:

     **Advanced Tab Settings**

     ![](https://sickk-services.gitbook.io/~gitbook/image?url=https%3A%2F%2Fcontent.gitbook.com%2Fcontent%2FGDLtbyiPkgQOjMQ1BLO0%2Fblobs%2FfBgysit648MCeXwuij65%2Fimage.png\&width=768\&dpr=4\&quality=100\&sign=14fcd18\&sv=2)

     * **Advanced EEE**: Disabled
     * **ARP Offload**: Disabled
     * **Flow Control**: Disabled
     * **IPv4 Checksum Offload**: Disabled
     * **Large Send Offload v2 (IPv6)**: Disabled
     * **Network Address**: Not Present
     * **TCP Checksum Offload (IPv6)**: Disabled
     * **UDP Checksum Offload (IPv6)**: Disabled

   *If a setting is unavailable, skip it.*
4. **Restart Your PC**

***

**Step 2: Flush and Reset Network Settings**

1. **Open Command Prompt (Admin)**
   * Press **Win + X**, select **Command Prompt (Admin)** or **Windows Terminal (Admin)**.
2. **Enter Commands (30-Second Delay Between Each)**
   * `ipconfig /flushdns`
   * `ipconfig /registerdns`
   * `ipconfig /release`
   * `ipconfig /renew`
   * `netsh winsock reset`
3. **Restart Your PC**
4. **Repeat Commands (With 5-Second Delay)**
   * Open Command Prompt (Admin) again and enter:
     * `arp -d`
     * `netsh interface IP delete arpcache`
5. **Restart Your PC Again**

***

**Step 3: Restart Your Router**

* Unplug your router, wait **30 seconds**, and plug it back in.

***

**IMPORTANT:** These steps ensure optimal performance and minimize detection risks. Always follow them carefully!